Concealed Equipment—(Tree and Misc., Equipment below).

Ideal for new construction. Cable and connections can be safely installed under roof and between walls with only the slender Rod protruding above the roof. (See FAQ #15)).

Tree Lightning Rods and Installation details

 Note: Aluminum Equipment should not be used in tree’s—Tree sap is destructive to aluminum.

Through the Roof Lightning Rod

Concealed Lightning Rod assembly in copper or aluminum.

Consists of 12” lightning rod with balance of rod threaded for roof insert. Nuts and washers draw tight to prevent leak, includes TEE for inside cable connection as shown.

 

Copper # C-34-24  12” Lightning Rod

above roof - 12” under roof.

(24” total length) $ 29.00

 

# C-34-30  12” above roof—18” under

roof  (30” total length)  $ 34.00

 

# C-34-36  12” above roof—24” under

Roof. (36” total length)  $ 40.00

 

Aluminum  # A-34-24    $ 23.50

                     # A-34-30   $ 27.50

                     # A-34-36   $ 31.50

Longer length’s are available.

Please specify Rod Lengths needed

above and below roof. Longer length

rods in copper are

$1.00 per inch.—.80 in aluminum.

 

Thru-Wall or Thru-Roof Cable Connector

Combination copper or aluminum connector used for thru the wall or roof penetration giving rigid attachment on both surfaces. These assemblies may be used in masonry construction with one end concealed. Both ends supplied with cable clamp connectors, stainless steel nuts and washers.

Rod length 12” (8” useable length) - other lengths available, add $1.00 per inch for copper—.80 for aluminum.

 

 

Copper      # C-35        $ 22.95

 

 

Aluminum # A-35      $ 17.95

 

 

 

Longer lengths available in

Copper $ 1.00 per inch.

.80 in aluminum

Tree Installation detail

Note 1: Locate ground approximately at branch line to avoid root damage. Install ground rod below edge of outer branches- bury cable and rod, connect below ground.

1. Main trunk air terminal (Rod's)

2. Main down cable

3. Branch air terminal (Rod's)

4. Branch cables

5. Drive type cable clip at 3 ft

6. Splicer (clamp)

7. Ground rod and clamp

8. A slender pine or palm tree usually would only require one  lightning Rod

9. Tree with a trunk diameter exceeding 3 ft. should have two cables down to two ground rods as widely separated as possible.

10. Only copper materials should be used in tree’s.

            Tree Lightning Rod

Copper cable and grounding equipment can be

Ordered from Lightning Equipment page 2

Copper Lightning Rod assembly consists of 36

Inch lightning rod with bolt tension cable

connector base. Furnished complete

with wood screws in base. (NOTE:

Aluminum not recommended

for tree’s)

Copper # C-36  (30” long) $ 39.50

 

Longer lengths available $1.00 per inch.

Tree Drive Cable Holders

Cast copper bronze tree drive to hold cable and lightning rod to

the tree.

Simply drive holder in tree and

compress ear around cable -

Holds firm to cable but allows

movement for growth or wind

sway.

 

 

Copper  # C-37      $ 2.40

Bolted Cable Clamp

General purpose clamp with stainless

steel bolt used to connect all cables.

 

 

 

Copper # C-10       $ 6.75

 

Economy Cable Strap

Copper loop fastener has 1/8” hole for copper Nail or Screws.

 

 

Copper # C-2   $ 0.30

 Copper Nails

 2 inches long

 

 

Copper # C-11    $0.12 each

>Home(1)  >Lightning Protection Equipment(2)   >Concealed & Tree Rods(3)   >Fancy Lightning Rods & Parts(4)  >More Fancy Rods(5)  >Whole House Surge Protection(6)  >WeatherVanes(7)  > Finials  (8)  >FAQ’s/Installation Details(9) >Order Form(10) >Photo’s/Misc. Parts(11)s— Pages: (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11)

                                                      ©No Reproduction of any images without written permission

Help protect your  maintenance personnel that are working on commercial type flat roof’s from injury and liability —Copper fixture fit’s over top of  3/8” and 1/2” diameter copper Lightning Rods.—$9.75—Sample mailed for $12.00 post paid.  (Set screw holds tight to the rod)

Not yet available in aluminum but we do have Blunt Tipped aluminum rods which you can replace for .80 per inch.

 

 Order Toll  Free

  877-866-3189

   Fax: (410) 734-0215

Email: Jim@LightningRodParts.com

#17-Z - 12” Lightning Rod for Standing Seam Roof in Copper $32.00

#A17-Z in Aluminum $25.60

Firmly bolts to roof seam with two stainless steel bolts. Comes complete with Lightning Rod, Cable clamp and swivel mount to keep rod plumb on sloped roof.

#17-18-Z In Copper with 18” rod $38.00

In Aluminum #A17-18-Z $30.00

SAFETY TIP                 STANDING SEAM

                                         ROOF ROD and MOUNT

Stands for Tall Rods

    18” Solid Copper Scroll Stand $79.00

    24” Solid Copper Scroll Stand $89.00

   18” Solid Copper plain stand $29.00

   24” Solid Copper plain stand $35.00

   36” Solid Copper plain stand $49.00

 18” Aluminum Scroll stand $39.00

 24” Aluminum Scroll stand $49.00

    18” Plated Steel plain stand $ 25.00

    24” Plated Steel plain stand $ 29.00

    36” Plated Steel plain stand $ 39.00

 Other sizes up to 48” available by special order

GROUNDING

Copper Ground Plate with Clamp

2 square foot x 0.032 thick copper flat plate.

Comes complete with attached clamp for ground cable.

 

 

 

Copper # C-24   $ 62.00

 

 

 

 

Use in place of Ground Rods

where shallow top soil is

encountered -

For soil depths of 1 to 2 ft.

Ground Rods and Ground Rod Clamps

LEFT: Ground Rod is 1/2” x 8’ long made of copper clad hardened steel. Long life corrosion resistant. Note: Never connect aluminum underground.

 

8’ Ground Rod (Left) #22  $ 19.00 (Note: Additional shipping due

to high shipping costs,  ground rods may be

available locally at less cost).

 

   Copper Ground Clamp (Right)  # C-23-A

      for 1/2” or 5/8” ground rods $11.00

 

       # C-23-B for 3/4” ground rods $14.00

 

Used for connecting copper cable to ground rod.

Will fit 1/2” - 5/8” - 3/4” ground rods. Two

stainless steel bolts with 2” contact length along

axis of the grounding rod.